Clic2Clic Laminate Flooring Installation VideosBe sure to view our two videos which illustrate how to install laminate flooring with the Clic2Clic system. One video describes preparations and the other installation of laminate flooring.

Clic2Clic-SystemCongratulations on your choice of Swiss Krono flooring. To help you achieve years and years of enjoyment from your new floor, we’ve put together this instructional guide to help you with proper installation and maintenance. To make installation even easier, Swiss Krono flooring features advanced Clic 2 Clic glueless locking technology .

Suitable subfloors for Swiss Krono laminate flooring are:

  • Existing floor surfaces including hardwood floors, linoleum, resilient vinyl, PVC (plastic floor surfaces must be permanently attached to the subfloor), needle felt, (dry) ceramic flooring.
  • Cement floors on all grades/elevations (maximum residual moisture 2.0 CM%). With a calcium chloride test, the maximum acceptable reading is 3.0 lbs/24 hours/1000 sq. ft.
  • Anhydrite and Anhydrite tiles (max residual moisture 0.3 CM%)
  • Magnesium Cement (max residual moisture 0.3 CM%)

Attention! Without a documented measurement of residual moisture content, a claim against the manufacturer for damages cannot be considered. Moisture content of wood subfloor must be less than 14%. Concrete subfloors must always be covered with a 6 mil vapor barrier even if linoleum, PVC or resilient vinyl is firmly attached to the concrete.

Be sure to visit these resource before you get started:

For guidance on how to care for your Swiss Krono laminate floor, please visit our Floor Care Recommendations.

Clic2Clic Laminate Flooring Installation Guide

IMPORTANT – Do not open immediately. Before opening, acclimatize planks for 48 hours by laying each box horizontally and individually in center of room where they will be installed. Make sure subfloor is clean, dry and flat. Always use safety glasses and a mask. Visit our website for more help.

Clic2Clic Laminate Flooring Installation Guide - 1Install vapor barrier if subfloor is cement (6 mil polyethylene film).
Clic2Clic Laminate Flooring Installation Guide - 2Always use an underlayment padding above the vapor barrier and below the laminate flooring planks. If pad is pre-attached, no additional underlayment should be used.
Clic2Clic Laminate Flooring Installation Guide - 3Install parallel to main light source; if no exterior light source, install parallel to longest wall.
Clic2Clic Laminate Flooring Installation Guide - 4If possible, start to lay panels under the door jam and finish installing planks on a wall without a door jam. See Working with Limited Clearance section, below.
Clic2Clic Laminate Flooring Installation Guide - 5Start placing panels so that tongue sides face the wall.
Clic2Clic Laminate Flooring Installation Guide - 6Remove the tongue on the panels that abut the walls to allow room for spacers and prevent problems from spills.
Clic2Clic Laminate Flooring Installation Guide - 7Lay panels close together on floor.
Clic2Clic Laminate Flooring Installation Guide - 8Rock and lock in half-length panel with rotating motion. Install first and second row at the same time. This will help ensure end joints are perfectly square. Planks forced down without properly engaging the tongue into the groove can result in damage.
Clic2Clic Laminate Flooring Installation Guide - 9Observe 3/8” clearances for expansion and 16” minimum for smallest usable piece.
Clic2Clic Laminate Flooring Installation Guide - 10Lock in panel lengthwise. Allow 12” minimum end-joint stagger row to row.
Clic2Clic Laminate Flooring Installation Guide - 11Use a 4”- 6” piece to hold the tongue and the groove on the same plane, limit end joint damage and ensure planks engage square. Tap end joints with multiple light taps, striking the tapping block evenly until end joints close. NOTE: Tapping too hard or striking the tapping block unevenly can result in installation-related damage or peaking.
Clic2Clic Laminate Flooring Installation Guide - 12To measure and cut last piece in a row, rotate offcut section 180°, mark accordingly, cut, rotate back 180° and slot into space.
Clic2Clic Laminate Flooring Installation Guide - 13Fit the last panel in the row using a pull bar.
Clic2Clic Laminate Flooring Installation Guide - 14Always allow for expansion around fixed objects.
Clic2Clic Laminate Flooring Installation Guide - 15An expansion gap T-strip is required when length of planks measures 40’ max and when width of planks measures 25’ max. Transition strips should be placed in all doorways directly under the door when the door is closed.
Clic2Clic Laminate Flooring Installation Guide - 16Cut the row along the wall to account for the unevenness of the wall while leaving 3/8” expansion room (2.5” minimum plank width).
Clic2Clic Laminate Flooring Installation Guide - 17Ensure floor is able to expand.

Problem Areas When Installing Laminate Flooring

Problem Areas When Installing Laminate Flooring - 1Some long edge joints cannot be installed using a 20° angle.
Problem Areas When Installing Laminate Flooring - 2Remove top part of the tongue and groove profiles.
Problem Areas When Installing Laminate Flooring - 3Use good quality wood glue to make the connection.
Problem Areas When Installing Laminate Flooring - 4Slide panel into space horizontally and slot into profile. Use these modified planks under door frames, radiators, cabinet fronts, etc. Use the pull bar to slide the planks where needed.